Ready to ditch your old liquid screen protector? Whether it’s worn out or you’re looking for a fresh display, removing it is the best way to keep your iPhone spotless and responsive. Unlike peel-off protectors, liquid layers require a bit more care.
You can safely remove the liquid coating without smudges or residue on your screen with a few basic tools and steps. To remove the liquid screen protector from the iPhone, soften the liquid layer with heat, apply screen polish, use a soft brush to remove particles, and wipe off the screen with a soft microfiber cloth. So, let’s dive into the details to do the magic.
Gather Necessary Tools to Remove the Screen Protector
Removing any screen protector is not a big challenge if you have the tools and follow the right method. To safely take off the liquid screen protector, you will need the following:
- Screen Polish: Get a suitable polish to apply to the screen.
- Microfiber Cloth: It will not allow any scratches to the screen.
- Soft Brush: A soft bristle brush helps to remove liquid particles.
- Cotton Swabs or Soft Tissues: They may be fine for small, deep cleans.
- Card: A bank card allows you to lift the screen protector.
How to Remove a Liquid Screen Protector Without Tempered Glass?
Removing the liquid screen protector from your iPhone without tempered glass is easy. However, you have to take proper care so that nothing goes wrong during this procedure. Here are a few easy steps that you can follow.
Step 1: Soften the Liquid Layer
Place your phone under the sun for an hour or two. The heat causes a breakdown of the bonding agent between the liquid and glass, which makes removal much easier. Avoid overheating your phone and monitor it to prevent any damage.
Step 2: Apply Screen Polish
Add screen polish specially formulated for mobile devices. You can find it in most smartphone repair shops. These polishes break up what remains of the protective layer.
Step 3: Use Soft Brush
Gently brush in small circular motions with a soft-bristle brush to lift the liquid particles from the screen. Be sure not to apply too much pressure, which may scratch the surface.
Step 4: Wipe Off the Screen
Remove all debris from the screen with a clean microfiber cloth. Pay special attention to the edges of the screen, where residue could collect. Repeat if necessary until the screen is clear and smooth.
How to Remove a Liquid Screen Protector with Tempered Glass?
If your liquid screen protector is installed together with tempered glass, then you’re in luck because the process will be very easy. The four simple steps below guide you to peel it off and return your screen to its original condition.
Step 1: Identify the Protector Layer
Typically, liquid screen protectors come in tandem with tempered glass, which applies just like a standard glass protector. However, remove the tempered glass and liquid layer as a single entity before pulling off the screen protector.
Step 2: Remove the Tempered Glass
Carefully lift one corner of the tempered glass using your fingernail or a thin plastic tool. Peel it off slowly, as the liquid screen protector is bonded together with the layers. Take your time so you don’t break it too sharply.
Step 3: Handle Cracked Tempered Glass
If it cracks, you can apply heat to loosen the adhesive. You can put your phone in direct sunlight so that the liquid layer will soften and thus make removal easier.
Step 4: Clean the Screen
Remove the protector and use a soft microfiber cloth to gently wipe away the remaining residue or particles. That’s it! Your screen or a new protector will now be clear and ready for use.
Are There Any Ways to Remove the Screen Protector from the Iphone?
Yes, multiple ways exist to remove the screen protector from the iPhone.
- Tempered Glass Protector: Using a plastic tool or fingernail, raise a corner slowly and then pull it off. Clean the screen using a microfiber cloth to remove any remaining residue from the screen.
- Liquid Screen Protector (No Glass): Place the phone in sunlight for about an hour to loosen the bond, then apply polish and gently brush it off.
- Cracked Tempered Glass: Gradually apply gentle heat with the sun or a hairdryer set on low. Then, slowly peel off the broken glass.
- General Tip: Always remove protectors slowly and clean the surface with a microfiber cloth to avoid scratches or leftover residue.
How Long Does a Liquid Screen Protector Last?
Liquid screen protectors usually last six months to two years, depending on how well they are applied and the surface’s usage. Premium ones can last up to five years or more. To extend the life of the screen protector, you should check it regularly and apply it again if necessary.
What Is the Difference Between Liquid and Tempered Glass Screen Protectors?
The tempered glass protectors are made of tough glass, and they give very good impact resistance and protection against drops while adding noticeable thickness to the screen. On the other hand, the liquid glass is a nano-coating that bonds invisibly to the screen and helps preserve the original look and feel of the phone while mainly providing scratch resistance. If the best protection against drop is the strength to be defined by tempered glass, then liquid glass provides useful advice for an ultra-thin, seamless finish.
Conclusion
In fact, removing the liquid screen protector from your iPhone is a process that requires patience. Since you won’t be able to make the liquid protector peel off like a typical glass protector, you should follow a dedicated method. Therefore, we have discussed a complete guide on how to remove the liquid screen protector from the iPhone.
For screens without tempered glass, apply heat to loosen the layer, add screen polish, and use a soft bristle brush to remove particles. While removing the protector with tempered glass, remove both protector and glass, remove the tempered glass, and clean the screen. If you’re not confident about applying, you can seek professional assistance from Tech City, as our professional technicians can handle all phone issues.